It is currently Wed Oct 18, 2017 12:30 pm

All times are UTC - 7 hours [ DST ]

Recent News:



Post new topic Reply to topic  [ 1 post ] 
Author Message
PostPosted: Mon Jul 03, 2017 4:40 pm 
Offline
1TB storage
1TB storage

Joined: Sun May 19, 2013 9:40 pm
Posts: 29
Thanks: 7
Thanked: 0 time in 0 post
Thought that since I was having so much grief completing a server restore using the HP method I'd try using the method forum member Diehard came up with. That is creating usb flash files for the server to boot from a la ex47x and 48x units instead of the 'updated" PXE method on the 49x / 510.

Instructions were straightforward and the restore was successful first time. However you do need the ability to pull the boot files from a hidden partition on an older generation WHS per the attached .pdf instructions. Or download a free .rar converter like 7-zip and use the downloaded files that Diehard kindly provided.

Diehard wrote:

https://1drv.ms/u/s!AkdpqdFoMwb7zFWoFEF7JXQ2xtju
https://1drv.ms/u/s!AkdpqdFoMwb7zFaQIb_5NWkY5PK4

Here is a link to my files. You have to add the image file from your EX490 DVD to the correct folder.


Either way you begin step 1 of the instructions by creating the bootable USB stick.

In step 2 you create the files for the bootable USB using files located on a hidden partition on the WHS. Note that after remotely disabling the WHS to get access to the hidden partition where the files you need are located and restarting so the changes would take effect, the health light did not stop blinking blue and the drive light stayed off. No worries, after waiting a sufficient time after reboot for the OS to load, just RDP in, open my computer, and you will see the hidden drive. Mine were marked in drive E:. Just copy and paste these files into a thumb drive to work on them (note that the sys vol information folder and the recycler folder was missing on my new ex47x install). That had no effect as the server successfully booted into recovery anyhow

Obviously using Diehard's .rar files would have been far faster. I figured that out afterwards... DOH.

In step 3 you are updating the files on the USB stick you pulled off the server and is a two step process. First is to replace the 47x NIC card driver that you took off the server with the one for the 49x. The specific driver version called for was a bit elusive. Rather than risking that the updated driver woudn't work for some crazy reason, I found it here:

http://drivers.softpedia.com/get/NETWOR ... K-XP.shtml

Second, your doing the same thing with boot.wim file from the server. Replace it with one from your ex49x server recovery disk (the instructions say restore disk but that is incorrect). Also make double sure your using the correct boot.wim file. The one that is located on the 49x recovery disk at D:\SOURCES is 116957kb. It is not the file specified in the instructions. The correct one is 120038kb and is located on the ex49x recovery disk in DVDdrive:\PXE\Boot.

In step 4 is actually a four step process. You will be preparing a new Recovery DVD disk as the OE disk will try to run the PXE boot stuff. You will need a EX47x recovery disk to get the base files from. Luckily, these are readily available in a bit torrent. Or of course, you can use the other .rar image Diehard provided.

First is to create a folder on your desktop to work on the files with and populate it with the appropriate 47x recovery files. Second, you will need to remove the ex47x Recovery image folder and replace it with the 49x image. Third do the same with the Home Server Connector Software folder. You are now ready to burn a new restore DVD. I burned it slowly and did data verification since the WHS v1 OS was now on it.

Step 5 is to complete the restore. I prepped the terminal (a w7/64) by turning off the anti-virus software and all three of the firewall profiles (thru control panel/Administrative tools/Windows Firewall with Advanced Security/View Firewall Properties.

The server and the terminal were both hard wired thru my router, not direct wired and I was not in safe mode. With the server off, install the usb stick in the lowest USB port on the back of the server and pull your primary drive out an inch so the server defaults into recovery mode (no more paperclip). Now run the new restore DVD up thru to the point the software asks you to start the server. At this point instead of starting the server, go ahead and hit next on the software, Now start the server, wait 5 seconds, and push the drive in.

Once the system tell you the restore was successful, remove the usb stick, restart, continue the recovery and setup the terminal.

That's it. Your done! and the best part is should there be a catastrophe, you can quickly and easily either restore or recovery from it now.

:beerme:


Attachments:
Creating a Bootable USB Drive for your EX49X.pdf [130.09 KiB]
Downloaded 19 times
Top
 Profile  
Thanks  

Attention Guest: Remove this ad by Registering with the MediaSmartServer.net Forums. It's Free!
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1 post ] 

All times are UTC - 7 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group